Out of Stock HS-CH 1500W Product Description: 2500W 240V AC Infrared Carbon Heater with remote control Comes with a remote control For both ceiling and wall mounting Produces instant and comfortable heat like the sun High heat efficient energy-saving comfort heat infrared carbon heater A robust and weatherproof heater designed for commercial and residential heating applications for indoor and outdoor Wattage 1500W Voltage 240V AC Amps 10A Phase I Material Aluminum, Plastic Rating IC Rated / Indoor and Outdoor use Grade of Protection IP 55 Application Restaurant / Garden / Stairways / Patios / Decks / Balcony areas / Walkways, etc. Colour Black Finish High-temperature resistant powder spraying Control ON/OFF switch Coverage Area 172.2-257.6 ft² Unit Dimensions 87.7 cm x 19.6 cm x 8.4 cm Warranty 1 year Installation This heater should be installed by a competent person (i.e. a qualified electrician) Always disconnect the heater from the electricity supply and allow it to cool before installation For ceiling mounting, the lowest part of the heater must be located or above a minimum height of 94-1/2" from ground level, so that the heater cannot be touched when in operation For ceiling mounting, there must be a 94-1/2" distance from your appliance to the ground When installed to the ceiling, there must be a distance of 19-11/16" between corners and the appliance The distance of your appliance from the living beings is to be one-meter minimum The distance from the front side of the heater to materials such as wood, carton, cloth, etc. must be a one-meter minimum When mounting to a ceiling, DO NOT position the heater at an angle more than 90º and less than 45º The supply cable must be at the lower end of the heater if the heater is installed at an angle or vertically Keep the supply cord away from the body of the heater which will get hot during use DO NOT install the heater on an inflammable surface Observe the minimum safe distance between the heater body and the inflammable surfaces when mounted The heater should always have a minimum clearance of 19-11/16" from a ceiling and adjacent walls If the heater is to be used outside, a weatherproof outlet is recommended Before drilling, ensure that there are no wires or water pipes in the area where the heater is to be installed The heater must be installed on the mounting brackets provided Fasten the brackets securely to the mounting surface and the backside of the heater using the nuts and screws supplied Fasten the heater securely on the brackets using the nuts and bolts supplied The brackets can be used to adjust the direction of the heater. Adjust the heater angle by loosening the two bolts on the wall mounting bracket. Tighten the bolts again when the desired angle is reached. Out of Stock
Out of Stock HS-CH 2500W Product Description: 2500W 240V AC Infrared Carbon Heater with remote control Comes with a remote control For both ceiling and wall mounting Produces instant and comfortable heat like the sun High heat efficient energy-saving comfort heat infrared carbon heater A robust and weatherproof heater designed for commercial and residential heating applications for indoor and outdoor Wattage 2500W Voltage 240V AC Amps 16A Phase I Material Aluminum, Plastic Rating IC Rated / Indoor and Outdoor use Grade of Protection IP 55 Application Restaurant / Garden / Stairways / Patios / Decks / Balcony areas / Walkways, etc. Colour Black Finish High-temperature resistant powder spraying Control ON/OFF switch Coverage Area 183-279.9 ft² Unit Dimensions 87.7 cm x 19.6 cm x 8.4 cm Warranty 1 year Installation This heater should be installed by a competent person (i.e. a qualified electrician) Always disconnect the heater from the electricity supply and allow it to cool before installation For ceiling mounting, the lowest part of the heater must be located or above a minimum height of 94-1/2" from ground level, so that the heater cannot be touched when in operation For ceiling mounting, there must be a 94-1/2" distance from your appliance to the ground When installed to the ceiling, there must be a distance of 19-11/16" between corners and the appliance The distance of your appliance from the living beings is to be one-meter minimum The distance from the front side of the heater to materials such as wood, carton, cloth, etc. must be a one-meter minimum When mounting to a ceiling, DO NOT position the heater at an angle more than 90º and less than 45º The supply cable must be at the lower end of the heater if the heater is installed at an angle or vertically Keep the supply cord away from the body of the heater which will get hot during use DO NOT install the heater on an inflammable surface Observe the minimum safe distance between the heater body and the inflammable surfaces when mounted The heater should always have a minimum clearance of 19-11/16" from a ceiling and adjacent walls If the heater is to be used outside, a weatherproof outlet is recommended Before drilling, ensure that there are no wires or water pipes in the area where the heater is to be installed The heater must be installed on the mounting brackets provided Fasten the brackets securely to the mounting surface and the backside of the heater using the nuts and screws supplied Fasten the heater securely on the brackets using the nuts and bolts supplied The brackets can be used to adjust the direction of the heater. Adjust the heater angle by loosening the two bolts on the wall mounting bracket. Tighten the bolts again when the desired angle is reached. Out of Stock
Out of Stock OFP-72LED Product Description Wattage High — 1300W / Low — 650W (2 levels of heating) Voltage 120V 60Hz Material One-piece log/stone and plastic crystals Installation Wall-mounted and built-in Timer 1-9 hours Control Mode Touch Panel / Remote Control Flame Colours 10 colours (9 colours + cycle) Flame Brightness 1 level (Brightness cannot be adjusted) Overheat Protection Yes Heating Area 16-20m² Installation Please take out the foam that is inside the unit before using the heater. Remove the glass panel first, set the firebox into the wall. Secure the side trim pieces on the wall with screws. Reinstall the glass panel onto the firebox with screws. Remove the outer glass around the bracket, mounting screws Remove the outer glass Take out the foam Install the outer glass to the appliance: Lift glass panel and line up with the top bracket, fasten the panel to the appliance. Screw the brackets to the appliance with mounting screws Be cautious about the outer glass bracket screws Glass Particles Installation To remove the outer glass around the bracket, undo the mounting screws Remove the outer glass Adjust the screws and carefully take out the log set Gently put the glass crystals into place Be cautious about the outer glass bracket screws Specifications Integrated remote control and touch control pad Has 3 ember bed selections which plastic crystals, one-piece log/stone consist Automatic overheating protection with a timer of 1 hour increments up to 9 hours Two-stage fan-forced air heater which you may use with the heater or without for ambiance Includes LED 9 color flame, one color cycle, and one-off status and the same applies to the side lighting Out of Stock
Out of Stock OFP-50LED Product Description Wattage High — 1300W / Low — 650W (2 levels of heating) Voltage 120V 60Hz Material One-piece log/stone and plastic crystals Installation Wall-mounted and built-in Timer 1-9 hours Control Mode Touch Panel / Remote Control Flame Colours 10 colours (9 colours + cycle) Flame Brightness 1 level (Brightness cannot be adjusted) Overheat Protection Yes Heating Area 16-20m² Installation Please take out the foam that is inside the unit before using the heater. Remove the glass panel first, set the firebox into the wall. Secure the side trim pieces on the wall with screws. Reinstall the glass panel onto the firebox with screws. Remove the outer glass around the bracket, mounting screws Remove the outer glass Take out the foam Install the outer glass to the appliance: Lift glass panel and line up with the top bracket, fasten the panel to the appliance. Screw the brackets to the appliance with mounting screws Be cautious about the outer glass bracket screws Glass Particles Installation To remove the outer glass around the bracket, undo the mounting screws Remove the outer glass Adjust the screws and carefully take out the log set Gently put the glass crystals into place Be cautious about the outer glass bracket screws Specifications Integrated remote control and touch control pad Has 3 ember bed selections which plastic crystals, one-piece log/stone consist Automatic overheating protection with a timer of 1 hour increments up to 9 hours Two-stage fan-forced air heater which you may use with the heater or without for ambiance Includes LED 9 color flame, one color cycle, and one-off status and the same applies to the side lighting Out of Stock
Out of Stock OFP-36LED Product Description Wattage High — 1300W / Low — 650W (2 levels of heating) Voltage 120V 60Hz Material One-piece log/stone and plastic crystals Installation Wall-mounted and built-in Timer 1-9 hours Control Mode Touch Panel / Remote Control Flame Colours 10 colours (9 colours + cycle) Flame Brightness 1 level (Brightness cannot be adjusted) Overheat Protection Yes Heating Area 16-20m² Installation Please take out the foam that is inside the unit before using the heater. Remove the glass panel first, set the firebox into the wall. Secure the side trim pieces on the wall with screws. Reinstall the glass panel onto the firebox with screws. Remove the outer glass around the bracket, mounting screws Remove the outer glass Take out the foam Install the outer glass to the appliance: Lift glass panel and line up with the top bracket, fasten the panel to the appliance. Screw the brackets to the appliance with mounting screws Be cautious about the outer glass bracket screws Glass Particles Installation To remove the outer glass around the bracket, undo the mounting screws Remove the outer glass Adjust the screws and carefully take out the log set Gently put the glass crystals into place Be cautious about the outer glass bracket screws Integrated remote control and touch control pad Has 3 ember bed selections which plastic crystals, one-piece log/stone consist Automatic overheating protection with a timer of 1 hour increments up to 9 hours Two-stage fan-forced air heater which you may use with the heater or without for ambiance Includes LED 9 color flame, one color cycle, and one-off status and the same applies to the side lighting Out of Stock
Out of Stock OFP-60LED Product Description Wattage High — 1300W / Low — 650W (2 levels of heating) Voltage 120V 60Hz Material One-piece log/stone and plastic crystals Installation Wall-mounted and built-in Timer 1-9 hours Control Mode Touch Panel / Remote Control Flame Colours 10 colours (9 colours + cycle) Flame Brightness 1 level (Brightness cannot be adjusted) Overheat Protection Yes Heating Area 16-20m² Installation Please take out the foam that is inside the unit before using the heater. Remove the glass panel first, set the firebox into the wall. Secure the side trim pieces on the wall with screws. Reinstall the glass panel onto the firebox with screws. Remove the outer glass around the bracket, mounting screws Remove the outer glass Take out the foam Install the outer glass to the appliance: Lift glass panel and line up with the top bracket, fasten the panel to the appliance. Screw the brackets to the appliance with mounting screws Be cautious about the outer glass bracket screws Glass Particles Installation To remove the outer glass around the bracket, undo the mounting screws Remove the outer glass Adjust the screws and carefully take out the log set Gently put the glass crystals into place Be cautious about the outer glass bracket screws Integrated remote control and touch control pad Has 3 ember bed selections which plastic crystals, one-piece log/stone consist Automatic overheating protection with a timer of 1 hour increments up to 9 hours Two-stage fan-forced air heater which you may use with the heater or without for ambiance Includes LED 9 color flame, one color cycle, and one-off status and the same applies to the side lighting Out of Stock
Out of Stock OFP-42LED Product Description Wattage High — 1300W / Low — 650W (2 levels of heating) Voltage 120V 60Hz Material One-piece log/stone and plastic crystals Installation Wall-mounted and built-in Timer 1-9 hours Control Mode Touch Panel / Remote Control Flame Colours 10 colours (9 colours + cycle) Flame Brightness 1 level (Brightness cannot be adjusted) Overheat Protection Yes Heating Area 16-20m² Installation Please take out the foam that is inside the unit before using the heater. Remove the glass panel first, set the firebox into the wall. Secure the side trim pieces on the wall with screws. Reinstall the glass panel onto the firebox with screws. Remove the outer glass around the bracket, mounting screws Remove the outer glass Take out the foam Install the outer glass to the appliance: Lift glass panel and line up with the top bracket, fasten the panel to the appliance. Screw the brackets to the appliance with mounting screws Be cautious about the outer glass bracket screws Glass Particles Installation To remove the outer glass around the bracket, undo the mounting screws Remove the outer glass Adjust the screws and carefully take out the log set Gently put the glass crystals into place Be cautious about the outer glass bracket screws Integrated remote control and touch control pad Has 3 ember bed selections which plastic crystals, one-piece log/stone consist Automatic overheating protection with a timer of 1 hour increments up to 9 hours Two-stage fan-forced air heater which you may use with the heater or without for ambiance Includes LED 9 color flame, one color cycle, and one-off status and the same applies to the side lighting Out of Stock
